Find Plaster/gypsum Dryer/gypsum Powder Dryer, Sodium Oxalate/Seasoner Granules Dryer, Silica Spin Flash Dryer on Industry Directory, Reliable Manufacturer/Supplier/Factory from China.

Inquiry Basket (0)
Home > Products > Elevated water tank > Aluminum Hydroxide Spin Flash Dryer

Aluminum Hydroxide Spin Flash Dryer

  • Aluminum Hydroxide Spin Flash Dryer
  • Aluminum Hydroxide Spin Flash Dryer
  • Aluminum Hydroxide Spin Flash Dryer
  • Aluminum Hydroxide Spin Flash Dryer

Aluminum Hydroxide Spin Flash Dryer

    Min. Order: 1 Set/Sets
    Transportation: Ocean
    Port: Shanghai,Ningbo,Qingdao

Product Description

Characteristics

Aluminium hydroxide is a kind of alkali. It is white crystalline powder, odorless and tasteless. When it reacts with alkali, it produces meta aluminate. Therefore, it's usually seen as a monohydrate metaluminic acid.

Descriptions

Aluminum hydroxide is one of the main raw materials for the production of aluminium fluoride by drying technique. The moisture content of aluminum hydroxide is 5-10%. However, the production process of dry aluminium fluoride requires that the moisture content of raw material aluminum hydroxide must be less than 0.1% after drying before it can be used in production.

The drying equipment used for drying aluminum hydroxide filter cake (solid content 15 ~ 20%) is mainly disc dryer, flash dryer and spray dryer. The filter cake dried by the disc dryer is like a brick needs to be crushed and grinded before the dry rubber powder can be produced for the preparation of catalyst, so its production processes are not continuous. Before the spray dryer drying, the aluminum hydroxide filter cake needs to be mixed with water for one time. The slurry is atomized by high pressure nozzle, and then entered into the drying room to dry. The product in powder form can be used in production directly. However, in the process of spray drying, it is necessary to dry the water of filter cake together, so the energy consumption and production cost of spray drying are high. On the contrary, flash dryer can be used for direct and continuous drying of aluminum hydroxide filter cake. The dried product in powder form can be used directly in the production of catalyst. Because flash drying process is simple and energy consumption is low, flash dryer is widely used.

The adoption of aluminum hydroxide flash drying system is to solve the problems of long process line, low production efficiency and large energy consumption, and the water content of aluminum hydroxide can not meet the requirements of dry aluminium fluoride production. The invention comprises a blower, a hot blast stove, a flash dryer, a double swirl dryer, a cyclone separator, a silo, a cloth bag dust collector, a draft fan, a blower and a hot blast stove, and a hot blast stove and a flash dryer. The flash dryer is connected with the double swirl dryer, the double swirl dryer is connected with the cyclone separator, the cyclone separator is connected with the bag filter, and the bag filter is connected with the induced fan. The invention has the advantages of short process flow, completely closed drying process, no impurity mixing, high quality of finished product, good operating environment, high thermal efficiency, short drying time and good energy saving effect.

Principle

The hot air enters the bottom of the dryer in the tangent direction. Driven by the agitator, a powerful rotating wind zone is formed. The slurry enters the dryer through the screw charger and rotates. Moving at high speed with powerful agitation function, materials are distributed under impact, friction and shear forces. The mass is quickly crushed and fully exposed to hot air, and then heated and dried. Dehydrated dry materials flow in hot air. The graded ring will stop and maintain the large particles, while the small particles will be removed from the center of the ring and collected in cyclone separator and dust collector. Incompletely dried or large pieces of material are transported by centrifugal force to the wall of the equipment, then be crushed again after they fell to the bottom.

Drying Process

The filter cake enters the flash drier under the action of the propelling speed of the screw pusher. In the process of falling, the cake was continuously crushed into fine particles by the impact and stirring of the rising heat flow. The fine particles go up with the hot air flow and dry, and enter the cyclone separator through the classifier for a single separation. After the separation, the product enters the discharging box. To ensure the stability of solid content, it is necessary to ensure that the outlet temperature of flash dryer is stable. The outlet temperature is controlled to ensure temperature stability by controlling the speed of the pusher. is agitated to form viscous slurry, which is deposited at the bottom of the putter. Under the push of the pusher, the slurry enter the flash drying chamber, and flows down the wall from the feed inlet to form an accumulation. When the accumulations are large enough, the paddle at the bottom of the flash tower touches the accumulations, which fall off the wall. The accumulation was dispersed by the agitator, fully mixed with the bottom hot wind, and the water evaporated a lot, resulting in a sharp drop in the outlet temperature, and the feed speed was reduced rapidly by the push feeder. Therefore, the temperature fluctuates in a wide range, thus affecting the stability of solid content of dry rubber products. When the condition is serious, the bottom of the tower will be blocked and the dust bag will be destroyed.

Features

● The collection rate of finished products is very high. Adopt the high efficiency low resistance cyclone separator (the collection rate can reach more than 98%), matching it with the pulsed jet cloth filter of gas chamber type (the collection rate can reach more than 98%).

● Effective control of final water content and fineness. The final water content and the fineness of the finished product are controlled by adjusting the sieve and inlet speed of the finished products.

● No wall adhesion. The continuous high flow of air will scour away the material left on the wall to prevent the phenomenon of the material remaining on the wall.

● This machine is good at processing heat sensitive materials. The bottom of the mainframe belongs to the high temperature area. The flow of air in this area is very high, and it is difficult for the material to directly contact the hot surface, so there is no need to worry about combustion and discoloration.

● The spin flash dryer supplied by Griffin is designed for continuous drying of viscous and non-viscous pastes and filters, as well as high viscosity liquids. The main components of spin flash dryer factory are feed systems, patent drying chambers and bag filters. The patented process has been widely praised by customers in various industries around the world, providing faster and more energy-efficient alternatives to spray drying. More than 100 Griffin spin flash dryer have been installed worldwide, integrating our experience and cutting-edge technology into our customers’ value-added solutions. Many products can use elevated drying temperatures because flash evaporation of surface moisture will immediately cool the dry gas without significantly increasing the product temperature.

● Disperse wet material into hot air (or gas) stream and conveying it through a drying pipe. Using the heat from the airflow, the material will be dried when it is transported. Use cyclone separator or pulsed jet cloth filter to separate products. Usually, the cyclone separator is followed by a scrubber or bag filter used to eventually clean the exhaust gas to meet current emission requirements.

● The feeding system consists of a feeding bucket. Before continuous drying the discontinuous materials are buffered and crushed through agitators. The variable feeding screw (or pump in the case of fluid feed) transfers the product to the drying room.

● The rotor at the conical bottom of the drying chamber causes the product particles to be fluidized in a dry and efficient hot air flow mode, by which any wet mass is decomposed fast. Hot air is supplied by a temperature-controlled air heater and a velocity-controlled fan to tangent into the drying chamber in order to create turbulent rotating airflow.

● The fine particles in the air pass through the classifier at the top of the drying chamber, while the larger particles remain in the air flow for further drying and pulverization.

● The drying chamber is strictly designed to withstand the pressure shock of combustible particle explosive combustion. All bearings are effective against dust and heat.

Technical Advantages

● Automatic protection Valve is installed on the inlet duct of bag dust catcher, which can protect cloth bag effectively by automatically entering cold air when it is overheated.

● The hot air duct at the bottom of the main engine adopts a bidirectional air inlet structure, which makes the inlet air more uniform and effectively avoids the deposition of materials due to uneven air separation.

● The hot blast furnace is made of high temperature resistant stainless steel and the inner tank adopts a special ring structure, which greatly reduces the temperature of the inner tank, ensures the cleanliness of the hot air and the quality of the product, and prolongs the service life of the hot air stove.


Application

● Organic substances: atrazine (pesticide), Lauric acid, benzoic acid, fungicides, sodium oxalate, cellulose acetate, organic pigments, etc.

● Dyestuff: Atrazine (pesticide), Lauric acid, benzoic acid, fungicides, sodium oxalate, cellulose acetate, organic pigments, etc.

● Inorganic substances: borax, calcium carbonate, hydroxide, copper sulfate, iron oxide, barium carbonate, antimony trioxide, various metal hydroxides, various heavy metal salts, synthetic cryolite, magnesium carbonate, alumina, aluminum hydroxide, carbon black white, etc.

Flowchart

image001



Griffin Technology Manufacturing Co., Ltd.

  • 1
  • 2
  • 3
  • 4
  • 5
 Griffin technology manufacturing Co,. Ltd, a factory with more than ten years experience of professional and technical industrial service. locates in Changzhou city of Jiangsu. Our company has 2 large modern construction machinery manufacturing plant, equipped with whole line of sheet metal bending, laser cutting, automatic polishing, automatic welding, occupies an area of 500,000 square meters. Also we have our own R&D team, which has a number of talents and individual test lab. We are specializing in researching and developing drying machine, such as spray dryer, mesh belt dryer, fluid bed dryer, flash dryer, air stream dryer, vacuum dryer, plate dryer and so on. As auxiliary machines of drying machine, we also supply mixer, granulator, grinder and screener, roller compactor, air flow mixing system and air flow conveyor. With rich experience, we keep leading in design and manufacturing Chinese herbal extract spray dryer, flavouring spray dryer, hydrolyzed protein spray dryer, desiccated coconut drying machine, coconut meat mesh belt dryer, pharmaceutical spray dryer, vegetable and fruit dehydrator (mesh belt dryer), bread crumb fluid bed dryer, enzyme spray dryer, chicken powder production line, seaweeds drying processing line, gelatin production, WDG production line and so on. Based on keeping stable quality of drying, mixing, granulating, crushing and sieving machines, we actively research and develop new product, like roller compactor, airflow conveying and mixing system, vacuum belt dryer, try to supply turnkey projects to our customers.

Company Info

  • Company Name: Griffin Technology Manufacturing Co., Ltd.
  • Representative: wanxingwei
  • Product/Service: Spray Dryer , Fluid Bed , Belt Dryer , Vacuum Dryer , Drying Equipment , Dryer
  • Capital (Million US $): 1170,000RMB
  • Year Established: 2002
  • Total Annual Sales Volume (Million US $): US$10 Million - US$50 Million
  • Export Percentage: 81% - 90%
  • Total Annual Purchase Volume (Million US $): US$5 Million - US$10 Million
  • No. of Production Lines: Above 20
  • No. of R&D Staff: 21 -30 People
  • No. of QC Staff: 51 -60 People
  • OEM Services Provided: yes
  • Factory Size (Sq.meters): 5,000-10,000 square meters
  • Factory Location: 198 Yunhe Road,Xinbei District,Changzhou,China
  • Contact Person: Mr. Frank
  • Tel: 86-17605290094
Email to this supplier
  • *Subject:
  • To:

  • *Messages:
    Your message must be between 20-8000 characters